Today we are going to be discussing How to Dry Laminate Flooring with Water Under it
Laminate flooring is popular because of its durability and strength, particularly in terms of resistance to wear and tear. This does not, however, eliminate the potential of water accumulating beneath your laminate floor. If you don’t dry the laminated floor with moisture underneath it quickly, you risk subfloor damage, mold, and a variety of other issues.
It takes several steps to dry laminate flooring holding water underneath it. You’ll have to take out the flooring, sanitize and dry each layer, dry and clean the subfloor, and then replace it. If it’s broken, however, you may have no choice but to replace it.
You may prevent the situation from getting worse by learning how to dry laminate flooring with water below it. Here’s what you should know if you’re not sure where to start.
How to Dry Laminate Flooring When There Is Water Under It (Step by Step Guide)
The technique for drying laminate flooring holding water underneath is long but simple. Here’s a step-by-step guide on drying laminate that has moisture underneath it.
- Get Rid of Moisture on Surfaces: If your laminate flooring has any water on the exterior surface, clean it up right away. This will help prevent any further moisture from getting under your floors. Leakages or droplets on the surface are usually easily cleaned with a dry cloth or towel.
If there’s a lot of liquid on the floor, don’t clean it with the cloth. If you do, the water may flow toward a seam, causing more water to infiltrate beneath your flooring. Instead, lay the cloth right on the leak and let it to absorb the liquid without pressing it.
While this method may necessitate more towels, it may lessen the likelihood of water entering beneath your boards.If it’s deep water, more durable equipment may be required. You can suction up standing water with a wet vac or a water pump. You can use the towel method above after you’ve removed most of it.
- Make use of Dehumidifiers or large fans: Dehumidifiers and blowers or fans can aid in the drying process. A dehumidifier is a machine that actively removes moisture from the air. Fans help to circulate the air and speed up the drying process. Not only will this aid with the cleanup, but it will also help with mold and mildew.
- Increase the temperature: You can also speed up the drying process by increasing the temperature. Adding warmth to the area, whether it’s by cranking up your HVAC system or putting a space heater in, can assist the moisture evaporate faster.
- Take off the Floorboards: After that, you’ll need to take out the floors. On the cleft side of the board, you should usually begin at the wall. Lift up one board per time after removing the trim. After you’ve deleted the first row, the remainder will be much easy to handle.
If you’re removing boards from a location that wasn’t affected by the leakage or spill, keep them separate from the ones that were. That way, the boards will stay dry.
- Get the Wet Flooring Dried: After you’ve taken all of the wet flooring, you’ll need to let the boards dry. To speed up the process, place them close the dehumidifier or fan. Also, make certain that the boards are kept flat. They might warp if they don’t.
The severity of a bend will determine whether or not it renders a board useless. In some circumstances, a warp will just complicate the reinstallation process. Reinstalling one floorboard, however, could injure other boards nearby if the bend is substantial. As a result, it may be preferable to replace it.
- Ensure that the underlayment is clean: The majority of laminate floors are laid over an underlayment to provide some padding. If yours has an underlayment, you’ll need to clean it up and get rid of any excess water.
Following that, it’s highly advisable to clean the underlayment. Start with a mixture of ammonia-free dish soap and warm water, depending on the type of spill. Grease or sticky substances may be broken down as a result, making them better to remove.
Allow for it to dry after you’ve finished. Then, to get rid of any mold or mildew, reclean it with a bleach solution. The underlayment may also need to be removed after that. While most of the pads are water resistant, not all of them are completely waterproof. If you don’t examine beneath the surface, you risk leaving moisture behind, which can lead to mold and damage.
It may also be necessary to replace the underlayment if it is damaged. The padding also decreases disturbance and makes your floor more pleasant underfoot, in addition to protecting your subfloor. Purchase new underlayment if you have any doubts about its condition or if the adhesive holding the parts together is frayed.
- The Subfloor should be dried and disinfected: After you’ve finished with the underlayment, you can move on to the subfloor. To clean off any standing water, use a dry cloth. Ensure to soak up the liquid rather than pushing it about, as this will prevent moisture from reaching dry areas of the flooring.
The subfloor should then be disinfected. You may also need to clean up the spill first, depending on the type. If the spill was not water, for example, you might want to start with some warm water and ammonia-free dish soap. You’ll be able to deal with the spill first this way.
After you’ve completed the initial cleaning, you’ll want to use a bleach solution. Mold and mildew can be prevented with bleach, as can odors. After scrubbing the area with the bleach solution, remove as much moisture as possible with a dry cloth. After that, let the subfloor exposed to allow it to dry.
If the dampness has been there for a long time and you notice symptoms of harm to your subfloor, it may be required to replace it. Twisting, de bonding, invasive or extensive mold, and other signs of damage suggest that there is a problem. Because your walkable area’s base is the subfloor, it’s important to make sure it’s in good repair. As a result, you may need to consult an expert to assess the problem.
- Clean the Floorboards: After the floorboards have dried completely, disinfect them. Start with a water and ammonia-free dish soap mixture and avoid wetting them while cleaning. After that, pat them dry using a clean towel. Then disinfect with a bleach solution.
While cleaning, look for any evidence of damage on the laminate. Deformation, bulging, cupping, or substantial warping, for example, could all be signs that the plank is too damaged to be reused. Sort the bad boards from the good ones.
If all of boards aren’t salvageable, you’ll be able to see just how much new flooring you’ll need. Allow the laminate flooring to dry for another 24 hours at this point. Before you begin fixing it, make certain that any moisture has been removed.
- Install the Underlayment: Before you install the new flooring, whether you’re utilizing fresh underlayment or what you had originally, you’ll need to put it back in place. You won’t need any glue because the underlayment floats. You must, however, double-check that the glue and tape are holding the parts together.
Check where the pad attaches to the wall and the connecting places between each piece if you’re trying to retain your existing underlayment. You’ll just need to readjust your underlayment till it’s back in place if they’re in decent shape.
When installing new underlayment, make sure to follow the manufacturer’s directions. Typically, the initial piece will be applied to one wall, a few inches just above floor. After you’ve secured that piece, use the adhesive strip to secure the next. Carry on in this manner till you reach the opposite wall.
- Restore your Laminate Flooring:You may restore your laminate flooring once the underlayment becomes in place. In most cases, the procedure is straightforward. The tabs on the boards insert into slots on adjacent boards.
As a precaution, you should refer to the manufacturer’s instructions when reinstalling. However, because most laminate flooring operate in the same way, this may not be essential. If all of your floorboards are reusable, you can just reinstall each board in just the same spot as before, obviating the necessity for cutting. However, based on the flooring they replace, you may need to cut them down if new floorboards must be brought in.
- Restore Your Trim:You’ll need to replace any removed trim after you’ve reinstalled the flooring. Just few wrap up nails and just a hammer are usually all that is required. Your project is now complete.
What is the Drying Time For Laminate Flooring?
It’s natural to have concerns regarding drying time while attempting to work out how to dry hardwood flooring with water below it. You may need to wait somewhere between 12 to 36 hours after the boards have been removed and huge fans or dehumidifiers have been turned on.
A large variance is caused by a number of variables. The flooring’s exact materials, relative humidity, present temperature, and saturation level all play an effect. The type of fans or dryers you use can also change the equation.
It’s vital to understand that if the floorboards aren’t removed, laminate flooring with dampness therein can take weeks to dry. It’s never an advisable to remove the flooring out if there’s water trapped beneath it because a lot of damage can happen in that period.
Is Mold Caused by Water Under Laminate?
Mold can grow under laminate if it gets wet. The speed at which it can happen is determined by the type of water involved. Mold can form in 24 to 48 hours in tap water from a pipe break, overflowing sink, or other similar issue. It might start in as little as 12 hours if you’re dealing with groundwater floods or sewage.
The timing for various types of fluids can differ. All moisture, on the other hand, has the capacity to encourage mold growth. As a result, if you really want to avoid a mold problem, you must act soon.
What are the Water Damage Symptoms on Laminate Flooring?
On laminate flooring, there are numerous symptoms of water damage. The following are a few of the most common:
- Odors of Mustiness
Any of these problems point to a problem. They could be symptoms of various problems as well as indicating water damage. Improper design and foundation problems, for example, could be the source of some of these problems. Because those indications indicate a potentially dangerous problem, you should investigate the situation right away to figure out what’s going on..
How to Restore Water Damaged Laminate Flooring?
In general, water-damaged laminate flooring cannot be repaired. If the boards have delamination, cracking, discolouration, substantial warping, soft patches, or other concerns, they should be replaced.
If you possess boards that might be recoverable, the first thing you should do is dry it out. This will allow you to assess its quality and determine whether or not it needs to be replaced. If it’s reusable, simply follow the steps outlined above to complete the repair. If not, you’ll need to replace the floorboard.
How to Keep Laminate Flooring From Getting Wet?
Water damage to laminate flooring can be avoided using a few different methods. First and foremost, quickly removing spills and leaks is an important part of the process. The chances of water going underneath the floorboards decrease when it doesn’t have the ability to sit on the face of the flooring.
Even if the water goes below the flooring, reacting quickly reduces the risk of permanent water damage. A sealant could be used as a preventative measure. Many possibilities, however, are incompatible with laminate, so check the manufacturer’s labels to see if there is a suitable product.
Otherwise, the best option is to build a waterproof laminate floor. In most circumstances, it is specifically created to keep water out. Keep in mind, though, that a catastrophic occurrence such as a flood could possibly allow water to get underneath.
How to Dry Laminate Flooring With Water Under it? – Bottom Line
Finally, if you’re attempting to find out how to dry laminate flooring with water below it, there’s a really simple procedure to follow. You can lessen the risk of damage by rapidly eliminating the moisture. Otherwise, you could have to remove the laminate and possibly fix the subfloor, and you might end up with mold.